Design House 545756 Instruction Manual

Browse online or download Instruction Manual for Sanitary ware Design House 545756. Design House 545756 Instructions / Assembly User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 1
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
8. With gasket in place, slide escutcheon over
trim sleeve. Fasten escutcheon to faucet body
and tighten to finished wall surface using two
mounting screws.
Design
House
3. Plaster guard is preinstalled. The front surface
of the plaster guard should sit flush with the finished
surface of the wall.
1. Shut off main water supply. Preparation/Assembly of
recommended component locations: Valve depth should be front of
valve to front of the finished wall of approx. 2-3/16" (1=7/8" - 2-1/2"
max); Shower and/or spout outlet hole should be 1-1/4" diameter,
and Valve access hole should be 6" diameter. Caution: Allow at least
2" between the tub outlet and tub rim.
2. Connect water supply lines using 1/2” threaded pipes and 90
degree elbows. Wrap all threaded connections with Teflon tape or
joint compound.
Note: water limit screw stops are preset at the factory if they are
present on valve. Modification is not required.
Pipe should stick outside
finished wall by 4”
Pipe should stick outside
finished wall by 4”
10. Insert screw through
handle and thread to
faucet body. Insert
button over set screw.
9. Slide handle onto
shaft.
Thread shower head onto shower
arm.
Wrap threaded connections (except where o-ring or rubber sealant are present)
with Teflon tape available from your local hardware or plumbing supply store.
Always wrap in a clockwise direction.
7a. Place handle on valve stem and turn handle to full on mixed
position. Turn on hot and cold water lines to full open for one minute
each. Check for leakage. Shut off water at faucet. Remove the
Handle. REMARK: Adjust the water temperature by adjusting the
red rotational limit. Remove the rotational limit stop from the valve
by sliding it off the stem. Rotate counter clockwise to increase
temperature or clockwise to reduce temperature. Re-install in
correct position.
6. Slip the spout onto the pipe
and tighten the screw to hold
spout in place.
7. To remove the plaster guard, loosen and
remove the 2 screws. Pull the guard straight out
to remove. Discard before installing escutcheon.
Trim sleeve will remain in place.
4.
4 4 4
5
5.
6
9
10
7
8
1 1/8”(35mm)
- 3 3/16”(80mm)
INSTALLATION PROCEDURE, CONTD.
MIDDLETON SINGLE
HANDLE TUB &
SHOWER FAUCET
Models 545772, 545764, 545756
48”(1200mm)
- 60”(1500mm)
8”(203.2mm)
Gasket
Washer
Cover
Screw
Screw
Screw
Plaster
Cartridge
Handle
Color button
Escutcheon
Spool
Spring
O-ring
O-ring
Body
Diversion valve
O-ring
Nut
Trim sleeve
Valve stem
19
18
17
16
15
14
13
07
06
05
08
24
25
Washer
Plug
Shower
Shower arm
Flange
Spout
23
22
21
20
26
27
09
10
11
12
04
03
02
01
Page view 0
1

Summary of Contents

Page 1 - SHOWER FAUCET

8. With gasket in place, slide escutcheon over trim sleeve. Fasten escutcheon to faucet body and tighten to finished wall surface using two mounting s

Comments to this Manuals

No comments