POP-UP (OPTIONAL) INSTALLATION PROCEDURE
MAINTENANCE
INSTALLATION PROCEDURE
TROUBLE SHOOTING
Under the Safe Drinking Water Act, the U.S. Environmental Protection Agency restricts the
amount of lead used in brass and solder. Your new faucet is made in strict compliance with
all government standards. The materials used in the manufacture of this faucet are of industry
standard quality and are similar to other plumbing products having brass fittings.
To reduce the amount of lead in your drinking water, allow the water to run for a moment before
filling your glass and remember to always use cold water for drinking purposes.
CONSUMER PROTECTION WARNING
• ALWAYS protect your eyes with safety glasses.
SAFETY TIPS
IMPORTANT POINTS
Helpful tools to install this faucet:
•
basin wrench
•
Teflon tape
•
(2) crescent wrenches
•
silicon sealer
•
flashlight
•
faucet supply tubes
Models 525840, 525832
TWO HANDLE
LAVATORY FAUCET
Design House is a registered
brand of DHI Corp.
Mequon, WI 53092
1-800-558-8700
1 2 3
21
SILICONE
SEALER
①
②
③
④
④
③
②
①
POP-UP INSTALLATION
EXPLODED PARTS
Pivot Rod & Ball
Stopper
Flange
Gasket
Nut
Body
Pivot nut
Clip
Strap
Screw
1A
2A
2B
2C
1B
3 4
⑦
⑥
⑤
④
③
②
①
②
①
③
Set Scew
Connect
Inverter
Bonnet
Cartridge
Washer
Base Plate
Mounting Nut
1. Shut off water supplies.
Remove old faucet. Place
gasket (1A) on bottom of
new faucet. Place faucet
though mounting holes in
sink. Secure faucet to sink
using mounting nuts (1B)
provided.
2. Make connections to water
lines. Use 1/2" IPS faucet
connections (2A) or use the
supplied coupling nuts (2C)
with 3/8" O.D. ball-nose
risers (2B). Use wrenches
to tighten connections. Do
not overtighten.
3. Important: After installation
is completed, remove aerator.
Turn on water supply and
allow both hot and cold water
to run for at least one minute
each. While water is running,
check for leaks.
Replace aerator.
Your new Design House faucet will give you years of trouble free performance.
Thank you for choosing a Design House product for your home.
Please read all of these instructions carefully before installing your new faucet.
• When installing your new faucet, hand tighten the connector nuts, then use one wrench to anchor
the fitting and a second wrench to tighten the nut one additional turn. Connections that are too tight
will reduce the integrity of the system.
• Wrap all threaded connections (except aerator thread in spout) with Teflon tape available from your
local hardware or plumbing supply store. Always wrap in a counter-clockwise direction.
Your new Design House faucet is designed to give you years of trouble free performance. Keep it
looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh
chemicals that will dull the finish and void your warranty.
Brass finishes are polished, then protected with a lacquer coating to help prevent tarnishing. Clean
these surfaces only with a damp, soft cloth.
Problem: Faucet leaks from under handle.
Cause: Bonnet is loose or o-ring on cartridge is
dirty or twisted.
Action:
1. Move handle to OFF position. Unscrew the set
screw on the side of the handle seat. Then
remove the entire handle assembly.
2. Tighten the bonnet by turning it clockwise.
Move the cartridge stem to the ON position.
The leak should stop around the cartridge
stem.
3. If the leak does not stop, shut off the water
supply. Remove the bonnet by turning it
counter clockwise. Lift out the cartridge valve.
Inspect the o-rings. Clear debris, untwist, or
replace if necessary.
4. Replace the cartridge making sure the wings
fit well into the cuts in the faucet body. Tightly
screw the bonnet onto the faucet body.
5. Reinstall the handle.
Problem: Faucet leaks around aerator or an
improper flow pattern.
Cause: Aerator is incorrectly fitted or is dirty.
Action:
1. Unscrew the aerator. Make sure all internal
parts are laying flat.
2. If there is debris, gently flush all parts inside.
3. Reinstall aerator.
Many of these parts come preassembled.
This exploded diagram is to assist in trouble
shooting.
1. Install Pop-up Assembly. Remove stopper (1)
and flange (2). Screw nut(3) all the way down.
Push gasket (4) down.
2. Apply plumber's putty or silicon sealer to the
underside of flange (1). Apply teflon tape to
threads at the top of body (2). Insert body (2)
into sink. Screw flange onto body. Pivot hole
(3) must face the back of the sink. Tighten
nut/gasket (4), do not overtighten.
Clean excess putty or silicon sealer.
3. Remove pivot nut (1). Install horizontal
rod (2) and stopper (3) as removable
(4) or non-removable (5). Hand tighten
pivot nut (1). Attach horizontal rod to
strap (6) using clip (7).
4. Insert lift rod (1) into strap (2) and
tighten screw (3).
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals